manualshive.com logo in svg

Mitsubishi Electric R16MTCPU, User Manual

Share
Download
Mitsubishi Electric R16MTCPU User Manual Download Page 53

3  INSTALLATION AND WIRING

3.3  Installation and Removal of SD Memory Card

51

3

3.3

Installation and Removal of SD Memory Card

This section describes the methods for installation of a SD memory card to the Motion CPU module, and removal.

Installation of SD memory card

When installing a SD memory card to the Motion CPU module, take note of the SD memory card position, and install using the 
following procedure.

Removal of the SD memory card

When removing a SD memory card from the Motion CPU module, remove the SD memory card using the following procedure.

1.

With the notch facing downwards, insert the SD memory card 
straight into the slot. After inserting check the SD memory card is 
inserted all the way in. If the SD memory card is not inserted 
properly, insufficient contact may cause an operation failure.

2.

The CARD READY LED flickers until the SD memory card can be 
used. When the CARD READY LED is ON, the SD memory card can 
be used.

3.

If the CARD READY LED does not turn on after installing a SD 
memory card, check that "SD memory card forced disable instruction 
(SM606)" and "SD memory card forced disable state (SM607)" are 
OFF.

1.

Hold the SD memory card control access switch for longer than 1s to 
stop access of the SD memory card.

2.

During the process of stopping access to the SD memory card, the 
CARD READY LED flickers, then turns OFF when the process is 
complete.

3.

After pushing in the SD memory card once, pull the SD memory card 
out straight.

SD memory card

CARD READY LED

CARD READY LED

SD memory card

SD memory card
access control switch

Summary of Contents for R16MTCPU



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands