manualshive.com logo in svg

Mitsubishi Electric R16MTCPU, User Manual

Share
Download
Mitsubishi Electric R16MTCPU User Manual Download Page 30

28

1  SYSTEM CONFIGURATION
1.3  Checking Production Information and Operating System Software Version

Checking operating system software version

The operating system software version can be checked with MT Developer2 or GX Works3.

Checking with GX Works3

Check on the product information list screen.

[Diagnostics] 

 [System monitor] 

 [Product Information List] button

Checking with MT Developer2

■

Installation screen

Check on the installation screen.

■

CPU information screen

Check on the CPU information screen.

[Help] 

 [CPU information]

■

Device

Check with the special register "Operating system software version (SD740 to SD747)". Refer to for details on special 
registers.

MELSEC iQ-R Motion Controller Programming Manual (Common)

Operating system
software version

Production information
of Motion CPU module

Operating system
software version

Production information
of Motion CPU module

Summary of Contents for R16MTCPU



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands