manualshive.com logo in svg

Mitsubishi Electric R16MTCPU, User Manual

Share
Download
Mitsubishi Electric R16MTCPU User Manual Download Page 50

48

2  EQUIPMENT SPECIFICATIONS
2.4  SSCNETIII Cables

Wiring process of SSCNETIII cable

Put the SSCNET

 cable in the duct or fix the cable at the closest part to the Motion CPU module with bundle material in order 

to prevent SSCNET

 cable from putting its own weight on SSCNET

 connector.

■

Putting in the duct

When putting in a duct, leave space for installing the module.

■

Bundle fixing

Optical cord should be given loose slack to avoid from becoming smaller than the minimum bend radius, and it should not be 
twisted. When bundling the cable, fix and hold it in position by using cushioning such as sponge or rubber which does not 
contain migratable plasticizing. If using adhesive tape for bundling the cable, fire resistant acetate cloth adhesive tape 570F 
(Teraoka Seisakusho Co., Ltd) is recommended.

Bundle material
Recommended product
NK clamp SP type (NIX,INC.)

Panel

Cable

Cord loose
slack

Motion CPU module

Base unit

Summary of Contents for R16MTCPU



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands