Mitsubishi Electric MAC-567IF Installation And Operation Manual Download Page 26 | Manualshive

Page: 26 / 68

background image

MELCLOUD

4. The LED display corresponds to that shown below when the connection has been established.

NOTE!

►

It can take a few minutes for the following display to appear.
(If the display does not change, press RESET for longer than 10 seconds, e.g. 14 seconds, to start
setup again beginning with 4.1.)

LED

Connected

Connected

Flashes (every 5 seconds)

Flashes (every 5 seconds)

4.5 Setup WPS-PIN mode

1. Before using WPS-PIN mode, the wi-fi adapter PIN has to be entered in the router.

Read the router instructions to learn how to enter the PIN.

2. To set WPS-PIN mode, press MODE for longer than 10 seconds and then release the button.
3. The LEDs NET and UNIT flash (every 5 seconds) when the connection has been made.

NOTE!

►

Verify that the router supports WPS-PIN mode.
Not all routers support WPS-PIN mode.

►

Press RESET for 2 seconds to reset the wi-fi adapter if the LED display has not changed after
5 minutes.

26

/ Software information 2019

«
...
24
25
26
27
28
...
»

Summary of Contents for MAC-567IF





































































Reviews:

No comments

Related manuals for MAC-567IF

Brand: Multitech Pages: 80

Zlinx Xtreme IP67 ZXT9-RM

Brand: B&B Electronics Pages: 164

Brand: Patton electronics Pages: 17

Brand: Tenda Pages: 52

Brand: ICP DAS USA Pages: 3

Brand: Vahle Pages: 16

Brand: Hama Pages: 7

Brand: MultiModem Pages: 88

Brand: Genexis Pages: 34

Brand: Four-Faith Pages: 22

ESTeem Horizon 216An

Brand: EST Pages: 104

Brand: Comnet Pages: 5

Brand: Ubee Pages: 74

Brand: NETGEAR Pages: 2

Brand: NETGEAR Pages: 2

EZ Connect SMC8014

Brand: SMC Networks Pages: 34

Brand: Viola Systems Pages: 21

Brand: TRENDnet Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands