Minebea Intec Puro Operating Instructions Manual Download

Page: 10 / 61

Symbol

Charge level

0 to 10 % Remaining
11 to 40 % Remaining
41 to 70 % Remaining
71 to 100 % Remaining

Note:

When battery symbol blinks fast, approximately 30 minutes working time is left.

When [lo.bat] is displayed, the scale will shut off.

Charging the scale must be performed in a dry environment.

WARNING

Risk of explosion can occur

If the rechargeable battery is replaced with the wrong type or if it is not properly
connected.

Battery is to be replaced only by an authorized Puro® service dealer.

Dispose of battery according to local laws and regulations.

3.4

Connections

Pos.

Description

Accessory

DC IN USB-C

Printer port

LC (load cell)

3.4.1

Connect platform

Connection of an analog Puro® platform, or a commercially available strain-gauge load
cell.

Turn the device off and disconnect it from power supply.

Turn the device upside down.

Remove the four rubber plugs at the rear side.

Weight indicator Puro®

3 Device installation

EN-8

Minebea Intec

Summary of Contents for Puro






























































Search results

Summary of Contents for Puro

Reviews:

Related manuals for Puro

Brands by name

Popular brands

Minebea Intec Puro, Operating Instructions Manual

Search results

Summary of Contents for Puro

Reviews:

Related manuals for Puro

Brands by name

Popular brands