Milwaukee M18 BLHPT, Original Instructions Manual

Page: 15 / 77

Deutsch
12 12
GB
English
TECHNICAL DATA
Press device
M18 BLHPT
Production code 4524 10 03 ...
... 000001-999999
Battery voltage 18 V
Power consumption 450 W
Nominal force 32 kN
Compression range :
Ø Plastics & Composite pipes
Ø Metal until
63 mm (110 mm)
54 mm (108 mm)
dep. on system
Weight according EPTA-Procedure 01/2014
(Li-lon 2,0 Ah) 2,9 kg
Weight
(M18 BLHPT / Li-Ion 2.0 Ah / J18-Th14) 4,7 kg
Noise information
Measured values determined according to EN 60745. Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) 76,5 dB (A)
Sound power level (Uncertainty K=3dB(A)) 87,5 dB (A)
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according
to EN 60745
Vibration emission valuea
h
<2,5 m/s 2
Uncertainty K= 1,5 m/s
2
WARNING!
The vibration emission level given in this information sheet has been
measured in accordance with a standardised test given in EN 60745 and may
be used to compare one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the main applications of
the tool. However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over
the total working period.
Identify additional safety measures to protect the operator from the effects
of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock,
fire and/or serious injury. Save all warnings and instructions for
future reference.
PRESS DEVICE SAFETY WARNINGS
Use protective equipment. Always wear safety glasses when working
with the machine. The use of protective clothing is recommended, such
as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear
defenders.
Never hold your fingers or other body parts in the working area of the
cylinder or the press jaws.
Do not hold the jaw levers with your hands during the pressing operation.
Press tools and press devices may only be used by trained personnel.
Check the press tools and press devices for cracks and other signs of wear
before each use.
Only use press tools and press devices that are in perfect technical
condition.
Have damage repared immediately by an authorised workshop.
The machine may only be used with a press jaw inserted into it.
In the event of problems during the pressing process, press the Emergency
Stop button immediately and release the ON switch. The valve will open
and the piston will return to its initial position.
Compliance with the specified service work and service intervals is
mandatory.
Remove the battery pack before starting any work on the appliance.
WORKING INSTRUCTIONS
Use only system-compatible press fittings and press jaws designed for
them.
Consult the documents provided by the system supplier for handling and
assembly instructions for fittings and pipes.
Check whether the nominal width of the press fitting corresponds to the
nominal width of the press jaws.
Make sure that the press jaw is fully closed when pressing is complete.
Imperfect pipe joints must be compressed again using a new fitting.
After finishing the work, check the installation with appropriate testing
equipment and assure that it is leakproof!
The press device is not suitable for continuous operation. Following 30
minutes of continuous operation, a short break of at least 15 minutes must
be taken to allow the device to cool down.
SPECIFIED CONDITIONS OF USE
The devices and the press jaws are designed exclusively for the press-
fitting of pipes and fittings for which the relevant press jaws are intended.
These press devices are intended exclusively for use with press jaws
approved by Milwaukee in agreement with the system supplier.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the
battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after use.
To obtain the longest possible battery life remove the battery pack from
the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery pack where
the temperature is below 27°C and away from moisture Store the battery
packs in a 30% - 50% charged condition Every six months of storage,
charge the pack as normal.
Do not dispose of used battery packs in the household refuse or by burning
them. Milwaukee Distributors offer to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit
risk).
Use only System M18 chargers for charging System M18 battery packs. Do
not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms.
Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse thoroughly
for at least 10 minutes and immediately seek medical attention.
No metal parts must be allowed to enter the battery section of the charger
(short circuit risk).