20
X
English
OVERLOAD AND KICKBACK PROTECTION
The power tool has an overload and kickback safety function and
stops if it is overloaded. Switch off the power tool and then switch
the power tool back on again in order to continue to work.
BRAKING SYSTEM
The run-on brake engages when the trigger is released, causing
the tool to stop within seconds.
Make sure that the insertion tool comes to a complete stop before
laying it down.
In comparison with tools without a run-on brake the run-on time
will be highly reduced by braking.
If the time between releasing the switch and the stop of the
insertion tool increases to much, please have the tool serviced by
an authorized MILWAUKEE service facility.
SOFT START
Electronic soft start for save use prevents jerky run-up of the
machine.
MAINTENANCE
Remove the battery pack before starting any work on the
appliance.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under “Technical Data” fulfills all the relevant provisions of the
directives
2011/65/EU (RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used.
EN 60745-1:2009 + A11:2010
EN 60745-2-3:2011+A2:2013
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-11-10
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that
the product described under „Technical Data“ fulfills all the relevant
provisions of the following Regulations
S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended),
S.I. 2016/1091 (as amended) and that the following designated
standards have been used:
BS EN 60745-1:2009 + A11:2010
BS EN 60745-2-3:2011+A13:2015
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-11-10
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Summary of Contents for 4933471075
