![background image](http://html.mh-extra.com/html/sealey/sm100/sm100_manual_1226599001.webp)
power belt sander 100 x 1220mm
750w/230V
model no:
sm100
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFetY
1.1.
eleCtrICal saFetY
warnInG!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey dealer.
1.1.1.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
1.1.2.
electrical safety information, it is important that the following information is read and understood.
1.1.2.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.2.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
8
do not
pull or carry the appliance by the power cable.
8
do not
pull the plug from the socket by the cable.
8
do not
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is
replaced immediately by a qualified electrician.
1.1.2.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
1.1.2.5. If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
1.1.2.6. Ensure that repairs are carried out by a qualified electrician.
1.1.2.7.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
1.1.2.8. ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.1.2.9. If an extension reel is used it should be fully unwound before connection. A reel with an RCd fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2.
General saFetY
9
disconnect the sander from the mains power before changing accessories, servicing or performing any maintenance.
9
maintain sander and belts in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
9
Replace or repair damaged parts.
Use genuine parts only. Unapproved parts may be dangerous and will invalidate the warranty.
warnInG!
Always work with the sander safety guard in place.
9
Wear approved safety goggles, ear defenders, appropriate dust mask if sander generates dust and safety gloves.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
9
Use sander in a suitable work area, keep area clean, tidy and free from unrelated materials, and ensure adequate lighting.
9
maintain correct balance and footing.
do not
over-reach and ensure the floor is not slippery. Wear non-slip shoes.
9
Check grinding disc to ensure they are not split, cracked or damaged in anyway. See chapter 4. If in doubt to not use the disc.
9
Grinding discs must be securely attached before use, but not over tightened.
9
Secure unstable workpiece with a clamp, vice or other adequate holding device, and ensure the sander is gripped with both hands.
9
Keep non essential persons away from the working area, use screens if necessary.
8
do not
operate the sander if any parts are missing or the sander is damaged.
8
do not
use the sander for a task it was not designed to perform.
8
do not
operate sander where there are flammable liquids or gasses.
warnInG!
do not
grind any materials containing asbestos.
8
do not
get the sander wet or use in damp or wet locations.
8
do not
switch the sander on whilst the belt is in contact with the workpiece.
8
do not
touch the workpiece immediately after grinding as it will be very hot.
8
do not
hold unsecured work in your hand, and
do not
touch the sanding belt whilst operating, or whilst plugged into the mains
power.
Refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Wear a mask
S
M100 | Issue:3 (H,F) 13/09/18
Original Language Version
© Jack Sealey limited
Recommended fuse rating
13 Amp