1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1.2.
GENERAL SAFETY
!
Familiarise yourself with the applications, limitations and potential hazards of the sander.
"
WARNING!
Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to.
"
WARNING!
Disconnect from the mains power supply before changing accessories, servicing or performing any maintenance.
"
"
WARNING! DO NOT
sand any materials containing asbestos.
!
Maintain and keep the sander in good condition (use an authorised service agent).
!
Check the alignment of moving parts regularly. For safest performance keep the sander clean at all times.
!
Before each use check all abrasive attachments for condition. If worn or damaged replace immediately.
!
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts are dangerous and will invalidate the warranty.
!
Locate the sander in a suitable work area. Keep the area clean, uncluttered and ensure that there is adequate lighting.
!
Ensure that the sander is situated on a solid work surface, adequate for supporting the weight of the sander and the workpiece.
!
Ensure that there are no flammable or combustible materials near the work area.
!
Remove ill fitting clothing, ties and loose jewellery and tie back long hair. Keep hands and body clear of the worktable when operating the sander.
!
Maintain correct balance and footing, ensure that the floor is not slippery and wear non-slip rubber soled footwear.
!
Wear approved safety eye or face protection, gloves, ear defenders and respiratory protection when operating the sander.
#
DO NOT
use the sander for any purpose other than that for which it is designed.
#
DO NOT
get the sander wet or use in damp or wet locations or areas where there is condensation.
#
DO NOT
operate the sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
#
DO NOT
touch the abrasive whilst operating, or whilst sander is plugged into the mains power and avoid unintentional starting.
#
DO NOT
switch the sander on while the workpiece is in contact with the abrasive and
DO NOT
leave the sander running unattended.
#
DO NOT
operate the sander if any parts are damaged or missing as this may cause failure and/or possible personal injury.
#
DO NOT
allow children or untrained persons to operate the sander. Keep them away from the work area.
#
DO NOT
remove the safety guard whilst sander is in use.
!
When not in use unplug from the mains power supply and make every effort to ensure the sander is childproof.
INSTRUCTIONS FOR:
BENCH-TOP BELT/DISC SANDER
Model:
SM14.V5
SM14.V5 - 2- 180907
1.1.
ELECTRICAL SAFETY
"
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity at Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6.
Important:
Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7.
DO NOT
pull or carry the appliance by the power cable.
1.1.8.
DO NOT
pull the plug from the socket by the cable.
1.1.9.
DO NOT
use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and
dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
To rewire, connect the wires as indicated above -
DO NOT
connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that a
suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm
2
, but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of
2.5mm
2
section cable.
FUSE RATING 5 AMP
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
