4
5
Cabinet Shelf
1
Cabinet Shelf Clip
4
NOTE:
Begin product assembly close to the final
intended location of your bench. This product is
heavy and may be difficult to move after assembly.
Attaching the Side Handle
Attach the side handle to the bench using four bolts
(CC). The side handle can be attached to either side
of the bench.
NOTE:
The holes in the bench are tapped and do
not require nuts.
Installing the Casters
CAUTION
Two people may be required to
complete installation.
CAUTION
Do not overtighten the screws.
1. Ensure all bench drawers are securely locked into
place using the key lock on the bench.
2. Lay the bench on its back. Use the packaging
material to protect the finish.
3. Mount the four swivel casters with brake to the
bench using four bolts (DD) per caster. The swivel
casters with brake should be installed on both ends
of the bench.
4. Mount the two rigid casters in the middle of the
bench using four bolts (DD) per caster.
5. Tighten all bolts securely with a wrench.
6. Return the bench to its upright position.
Installing the Drawer Liners
Place the drawer liners in appropriately sized drawers
to protect the surface.
Installing the Bumpers
Attach the four bumpers to the bench using two bolts
(EE) per bumper.
Installing the Cord Storage Brackets
Attach the brackets to the bottom right of the bench
power strip with two bolts (AA) per bracket. Orient
the brackets with one pointed up and one pointed
down so that the power outlet cord can be wrapped
around the brackets for storage.
Attaching the Tool Hanger
Attach the tool hanger to the left end of the bench
using two bolts (CC).
Attaching the Storage Shelf
Attach the storage shelf to the bench using two bolts
(CC) on either end of the bench.
Positioning the Peg Board
CAUTION
Do not hang any objects on the peg
board without securing the board
in place.
The peg board is shipped and secured in its stored
location. To raise the peg board to a usable height,
remove the locking thumb screws at the top of the peg
board slides. The peg board can be raised to either
mid or full height position by pulling straight up. When
in mid or full height position, two pairs of ball detents
will temporarily hold the peg board in place. The lock-
ing thumb screw holes and the tapped holes located
in the frame of the peg board will align. Reinstall the
locking thumb screws to secure the peg board.
Hardware Included
NOTE:
Items not shown to actual size.
Hard-
ware
Item
Description
Quantity
AA
Service Part
Description
Quantity
AA
BB
Bolt M6 x 15L
12
CC
Bolt 1/4" x 3/4"L
6
Bolt M4 x 10L
4
Service Part
Description
Quantity
Bolt M8 x 15L
24
DD
1
EE
Screw M4 x 10L
8
BB
Service Part
Description
Quantity
AA
BB
Bolt M6 x 15L
12
CC
Bolt 1/4" x 3/4"L
6
Bolt M4 x 10L
4
Service Part
Description
Quantity
Bolt M8 x 15L
24
DD
1
EE
Screw 1/4" x
3/4" L
4
CC
Service Part
Description
Quantity
AA
BB
Bolt M6 x 15L
12
CC
Bolt 1/4" x 3/4"L
6
Bolt M4 x 10L
4
Service Part
Description
Quantity
Bolt M8 x 15L
24
DD
1
EE
Bolt M6 x 15L
12
DD
Service Part
Description
Quantity
AA
BB
Bolt M6 x 15L
12
CC
Bolt 1/4" x 3/4"L
6
Bolt M4 x 10L
4
Service Part
Description
Quantity
Bolt M8 x 15L
24
DD
1
EE
Bolt M8 x 15L
24
EE
Screw M6 x 15L
8
FF
Service Part
Description
Quantity
AA
BB
Bolt M6 x 15L
12
CC
Bolt 1/4" x 3/4"L
6
Bolt M4 x 10L
4
Service Part
Description
Quantity
Bolt M8 x 15L
24
DD
1
EE
Wrench
1
Item
Description
Quantity
Side handle
1
Tool hanger
1
Swivel caster with
brake
4
Rigid caster
2
Bumper
4
Cord Storage
Bracket
2
Peg Board Bracket
2
Locking Thumb
Screw
2
CAUTION!
The locking thumb screws must be
installed before hanging objects on the peg board.
For increased stability of the peg board, peg board
brackets and hardware are provided. To install
brackets, locate the tapped holes on both ends of
the peg board, just above the bench work surface.
Mount the peg board brackets on both ends of the
peg board frame using two bolts (CC) per bracket.
With the foot of the bracket resting in position on the
wood work surface, mark the position of each bracket
hole and drill 1/8” holes approximately ¾” deep. Use
bolts (BB) to secure the peg board brackets to the
wood work surface.
Reversing the Wood Work Surface
The wood work surface comes pre-installed with
the bench. After wear and tear, the surface may be
reversed to use the clean bottom surface. To reverse,
remove the eight bolts from the top of the wood work
surface, flip surface, and reinstall the eight bolts.
OPERATION
WARNING
To avoid injury or property damage,
do not exceed maximum shelf and
drawer capacity. Use care when moving bench
on incline or rough surface. Bench may tip if
weight is not evenly distributed front to back and
side to side. Place more than half the total load
weight on the bottom drawers when possible.
Locking and Unlocking the Bench
NOTE:
The drawers must be fully closed before
locking/unlocking the unit.
Insert the key. Turn it fully left to lock, or fully right
to unlock. Always remove the key after locking and
unlocking.
