4
5
ASSEMBLY
Symbology
Read Operator’s Manual
Double Insulation
Risk of Electric Shock
Earth (Ground)
Danger, Warning, or Caution -
Consult the operators manual for
additional safety information.
Battery
European Conformity Mark
Underwriters Laboratories, Inc.,
United States and Canada
1
Canadian Conformity Mark
Cat III
Classi
fi
cation of transient
overvoltages, based on nominal
line voltage to earth.
Fuse
Do not dispose of this product as
unsorted municipal waste.
WARNING
To avoid an electrical hazard,
turn the rotary dial to OFF and disconnect the
test leads before replacing batteries.
Dial Position
Range
Resolution
Accuracy
Voltage AC
6mV-600mV/6V/
60V/600V
0.1mV/0.001V/
0.01V/0.1V
±(1.0% + 3 dgt) (45~500Hz)
±(2.0% + 3 dgt) (500~1000Hz)
Voltage DC
600mV/6V/
60/600V
0.1mV/0.001V/
0.01V/0.1V
±(0.5% + 2 dgt)
Hz
Hz
Hertz
2Hz-99.99Hz/999.9Hz/
9.999kHz/50kHz
0.01Hz/0.1Hz/
0.001kHz/0.01kHz
±(0.1% + 2 dgt)
Sensitivity: 10Vp-p
Resistance
600
Ω
/6k
Ω
/60k
Ω
/
600k
Ω
/6M
Ω
0.1/0.001k/0.01k/
0.1k/0.001M
Ω
±(1.0% + 5 dgt)
±(1.0% + 5 dgt)
40M
Ω
0.01M
Ω
±(2.0% + 5 dgt)
Continuity
Cont Buzzer
0-600.0
Ω
0.1
Ω
Beeper sounds at 30
Ω
and below
Capacitance
100
μ
F / 1000
μ
F
0.1
μ
F / 1
μ
F
±(1.9% + 2 dgt)
Current AC
0.04A - 6A / 10A
0.001A/0.01A
±(1.5% + 3 dgt) (45~500Hz)
Current DC
6A/10A
0.001A/0.01A
±(1.0% + 3 dgt)
Functions
* This is a True-RMS instrument. All AC voltage and
AC current readings are True-RMS values.
* Input impedance: Voltage DC: 10M
Ω
; Voltage AC:
10M
Ω
// less than 100pF
* Overload protection:
Voltage DC, Voltage AC, and Hertz: AC/DC 720V for
10 second
Current DC & Current AC: AC/DC 20A for 10 sec.
Resistance, Continuity, and Capacitance: AC/
DC 600V for 10 second
* Maximum measurement time: 1 minute at 10A, rest
time 20 minutes minimum
* Minimum frquency measurement is 2Hz
* Minimum AC Current measurement is 0.040A
* For AC Voltage, and AC Current:
Additional Accuracy by Crest Factor (C.F.): Add
6.0% for C.F. 1.0 ~ 2.0
Add 7.0% for C.F. 2.0 ~ 2.5
Add 9.0% for C.F. 2.5 ~ 3.0
Max. Crest Factor: 1.6 for 6600 ~ 5000 digits
2.0 for 5000 ~ 3000 digits
3.0 for 3000 ~ 0 digits
* Measurement accuracy of square wave and trun-
cated waveforms at 1kHz is unspeci
fi
ed.
Changing the Batteries
Replace batteries when the low battery indicator
is displayed.
1. Turn rotary dial to OFF and disconnect the test
leads.
2. Unscrew and remove
battery door.
3. Insert two (2) AA batteries,
according to the polarity
marked in the battery
compartment.
4. Close the battery door and
tighten screws securely.
OPERATION
Before Use
Con
fi
rm the rotary dial is set to the correct position,
the instrument is set to the correct measurement
mode, and the hold function is disabled. Otherwise,
desired measurement cannot be made.
LCD Backlight
Press the backlight button to turn the LCD back-
light on and off. The backlight will turn off after about
10 minutes of inactivity and can be turned back on
by pressing the backlight button again.
DANGER
To avoid electrical shock:
Never make measurement on a circuit in
which voltage over 600 volts AC exists.
Do not use with the battery cover removed.
Keep
fi
ngers behind the guards and away
from test lead tips during measurements.
CAUTION
Readings may
fl
uctuate or
be in
fl
uenced in noisy environment.
1. Set the dial to
position.
2. Connect the red test lead to the
V
Ω
terminal and the black test
lead to the COM terminal.
3. Connect the test leads to the
circuit under test. The reading
is displayed.
1. Set the dial to position.
2. Connect the red test lead to the
V
Ω
terminal and the black test
lead to the COM terminal.
3. Connect the red test lead to the
positive (+) side and black test
leads to the negative (-) side of
the circuit under test.
The reading is dis-
played. A reversed
connection is indi-
cated as a negative
value.
DANGER
To avoid electrical shock:
Never make measurement on a circuit in
which voltage over 600 volts DC exists.
Do
not use with the battery cover removed. Keep
fi
ngers behind the guards and away from test
lead tips during measurements.
DC Voltage
WARNING
Only use
MILWAUKEE
test
leads with the
MILWAUKEE
Digital Multimeter.
Inspect test leads for continuity before each
use. Do not use if the readings are high or
noisy.
0
V
AC
0
V
DC
Making a Measurement
AC Voltage
