Miele WWB 020 Operating Instructions Manual Download Page 76

Page: 76 / 80

Programmable functions



Chlorine bleach

You can activate the automatic
addition of chlorine bleach at the end
of the main wash.

Chlorine bleach may only be used in
some programs. See “5. Adding
detergent – Using chlorine bleach” for
more detailed information.

Activating chlorine bleach extends the
program duration by approximately
10 minutes.

Options



= Chlorine bleach is switched off

(factory default setting)



= Chlorine bleach is switched on



Display brightness dimmed

The brightness of the dimmed sensor
buttons on the control panel can be
set to one of seven different levels.

The brightness will change as soon as a
different setting is chosen.

Options



= Darkest level





= Brightest level



(Factory default setting)



Welcome tone

The welcome tone sounds whenever
the washing machine is switched on.

You can switch the welcome tone on or
off.

Options



= Welcome tone is switched off



= Welcome tone is switched on

at normal volume

(factory

default setting)



= Welcome tone is switched on

at loud volume

Summary of Contents for WWB 020

















































































Search results

Summary of Contents for WWB 020

Reviews:

Related manuals for WWB 020

Brands by name

Popular brands

Miele WWB 020, Operating Instructions Manual

Search results

Summary of Contents for WWB 020

Reviews:

Related manuals for WWB 020

Brands by name

Popular brands