Miele WWB 020 Operating Instructions Manual Download Page 26

Page: 26 / 80

5. Starting a program

Starting a program



Touch the flashing

Start/Stop

sensor

button.

The door will lock and the program will
start.

– As long as the



symbol is flashing

on the control panel, you can add
laundry.

– When the



symbol lights up

constantly, the door is locked until
the end of the program.

If a Delay start time has been selected,
this will count down on the time display.
At the end of the Delay start time or
immediately after the program has
started, the program duration will
appear in the time display.

Energy savings

After 10 minutes, the indicators dim.
The

Start/Stop

sensor button will flash

slowly.

You can reactivate the indicators:



Touch the

Start/Stop

sensor button

(this does not have any effect on a
running program).

Summary of Contents for WWB 020

















































































Search results

Summary of Contents for WWB 020

Reviews:

Related manuals for WWB 020

Brands by name

Popular brands

Miele WWB 020, Operating Instructions Manual

Search results

Summary of Contents for WWB 020

Reviews:

Related manuals for WWB 020

Brands by name

Popular brands