background image

Environmentally friendly washing

16

Energy and water consumption

– To get the most out of your machine,

load the maximum dry load for the
program you are using.
The energy and water consumption
will then be the lowest in relation to
the size of the load.

– When smaller amounts of laundry are

washed, the automatic​ load
recognition system will reduce the
amount of water and energy used.

– Use the 

Express

 program for smaller,

lightly soiled loads.

– Modern detergents make it possible

to wash at lower temperatures (e.g.

20°C

). Using the corresponding

temperature settings will save energy.

– To maintain the hygiene of the

machine, carry out a hot wash above
60°C at regular intervals. The

 indicator will come on to remind

you to carry out a hot wash.

Detergent consumption

– Do not exceed the amounts of

detergent recommended on the
packaging.

– Adjust the dosage to the level of

soiling of the laundry.

– Reduce the amount of detergent with

smaller loads (approx. ⅓ less than
the amount recommended can be
used when washing a half load).

When drying with a tumble dryer

Select the highest possible spin speed
for the wash program to save energy in
the subsequent tumble dryer cycle.

Summary of Contents for WWB 020

















































































Reviews: