Miele WMR561WPS Operating Instructions Manual Download Page 66

Page: 66 / 112

Cleaning and care

Cleaning the siphon tube and the
channel

Liquid starch can cause the siphon
to become clogged. Make sure that
you clean the siphon and siphon
tube particularly thoroughly after
using liquid starch a few times.



Clean the siphon.

1. Remove the siphon from the



compartment and rinse under hot
running water. Clean the siphon tube
at the same time.

2. Replace the siphon.



Clean the fabric conditioner channel
with a brush and hot water.

Cleaning the detergent dispenser
drawer housing



Use a bottle brush to remove
detergent residues and limescale
from the jets inside the detergent
dispenser drawer housing.



Replace the detergent dispenser
drawer.

Tip:

Leave the detergent dispenser

drawer slightly open to allow it to dry.

Summary of Contents for WMR561WPS

















































































































Search results

Summary of Contents for WMR561WPS

Reviews:

Related manuals for WMR561WPS

Brands by name

Popular brands

Miele WMR561WPS, Operating Instructions Manual

Search results

Summary of Contents for WMR561WPS

Reviews:

Related manuals for WMR561WPS

Brands by name

Popular brands