Miele WMR561WPS Operating Instructions Manual Download Page 20

Page: 20 / 112

Before using for the first time

Starting the calibration
programme

For optimum water and energy
consumption and excellent wash
results, it is important to calibrate the
washing machine.

The following message appears in the
display:



Open the stopcock and run the Cottons

90°C programme without laundry.



Confirm the message with the

sensor.

To do this the

Cottons 90 °C

must

started without laundry and without
detergent.

No other programmes can be started
until calibration has been carried out.



Open the stopcock.



Turn the programme selector to

Cottons

10:30

90°C

1600

rpm

Duration

1:55



Press the

Start/Stop

button.

The calibration programme has started.
This will take approx. 2 hours.

At the end of the programme the
following message will be displayed:



Set up completed



Take hold of the door and pull it
open.

Tip:

Leave the door slightly open to

allow the drum to dry.



Switch the washing machine off with
the



button.

Summary of Contents for WMR561WPS

















































































































Search results

Summary of Contents for WMR561WPS

Reviews:

Related manuals for WMR561WPS

Brands by name

Popular brands

Miele WMR561WPS, Operating Instructions Manual

Search results

Summary of Contents for WMR561WPS

Reviews:

Related manuals for WMR561WPS

Brands by name

Popular brands