Miele WMH122 WPS Operating Instructions Manual Download Page 65

Page: 65 / 104

Problem solving guide

A message appears in the display at the end of the programme

Message

Cause and remedy



Check jet

The pumps are dirty.



Clean the pumps as described in "Problem solving
guide - Opening the door in the event of a blocked
drain outlet and/or power failure"



Start the programme again after cleaning the
pumps.

The jet in the top of the door ring is blocked with fluff.



Remove the fluff with your finger. Do not use any
sharp or pointed tools to do this.



Start the programme again after cleaning the jet.

If the fault message appears again, contact the Ser-
vice Department. The washing machine can still be
used but with reduced functionality.



Align the machine

The smoothing process which the laundry undergoes
at the end of the programme could not be carried out
properly.



Check whether the washing machine is aligned
correctly as described in "Installation and connec-
tion - Levelling the machine".



Check whether the maximum delivery height of
1 m has been exceeded.

If the fault message appears again, contact the Ser-
vice Department. The washing machine can still be
used but with reduced functionality.

The messages will appear at the end of the programme and when the washing
machine is switched on and need to be confirmed with the

sensor.

Summary of Contents for WMH122 WPS









































































































Search results

Summary of Contents for WMH122 WPS

Reviews:

Related manuals for WMH122 WPS

Brands by name

Popular brands

Miele WMH122 WPS, Operating Instructions Manual

Search results

Summary of Contents for WMH122 WPS

Reviews:

Related manuals for WMH122 WPS

Brands by name

Popular brands