Miele WCE 660 Operating Instructions Manual Download Page 64

Page: 64 / 100

Problem solving guide

Messages or faults with the TwinDos system

Problem

Cause and remedy



Cartridge 1 almost
empty. Only a few
more programmes
are possible

The detergent in the cartridge is running low. There is
sufficient left for approx. 4 to 8 wash programmes.



Order a new cartridge.



TwinDos  is
empty. Check wash
results

The cartridge is empty.



Replace the cartridge.



Check whether the laundry is clean. If it is not,
there may not have been enough detergent.
Wash the laundry again if necessary.



Use "TwinDos" or
start Maintenance.
See 

TwinDos or automatic dispensing via compartment



and/or



has not been used for a long time.



Use TwinDos for one of your next loads.



Carry out the TwinDos maintenance programme as
described in “Cleaning and care - TwinDos
maintenance”.



TwinDos
Maintenance for
compartment 
must be started. See


TwinDos or automatic dispensing via compartment



and/or



has not been used for a long time. It is

possible that detergent has dried inside the hoses.



Carry out the TwinDos maintenance programme

immediately

as described in “Cleaning and care -

TwinDos maintenance”.

No detergent was
dispensed.

Automatic dispensing is deactivated.



Before the next wash programme, ensure that the

TwinDos

sensor control is lit.

Detergent is not dispensed even though the

TwinDos

sensor control is lit.



Try again.



If detergent is still not dispensed, call Miele.

The messages shown on this page are examples. They may differ depending on
whether they refer to compartment





Summary of Contents for WCE 660





































































































Search results

Summary of Contents for WCE 660

Reviews:

Related manuals for WCE 660

Brands by name

Popular brands

Miele WCE 660, Operating Instructions Manual

Search results

Summary of Contents for WCE 660

Reviews:

Related manuals for WCE 660

Brands by name

Popular brands