Miele TMG 440 WP Operating Instructions Manual Download Page 76

Page: 76 / 84

Settings menu

Calling up settings

You can use the Settings menu to alter

the dryer's electronics to suit different

requirements. Settings can be altered

at any time.

Opening the Settings menu



Switch the dryer on.

The programme selector must not be at

the

Further programmes

position.



Touch the



and



sensors at the

same time.

The following will light up in the display:

Language 



You are now in the Settings menu.

Selecting a setting



Touch the





sensor until the

setting you want appears in the

display.

– The



sensor scrolls down the list.

– The



sensor scrolls up the list.



Confirm by touching the

sensor.

Changing a setting



Touching the





sensor will call

up the different options for the

setting.

For example, you can

– select a value. If the option is marked

with a



, it is active,

– change a bar chart,
– change numbers.



Confirm by touching the

sensor.

Closing the Settings menu



Touch the





sensor repeatedly

until

Back



appears in the display.



Confirm by touching the

sensor.

Language



The display can be set to appear in

one of several different languages.

The flag



after the word Language

acts as a guide to prevent a language

which will not be understood from

being set.

Summary of Contents for TMG 440 WP





















































































Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands

Miele TMG 440 WP, Operating Instructions Manual

Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands