Miele TMG 440 WP Operating Instructions Manual Download Page 34

Page: 34 / 84

Programme overview

Proofing

Max. load 2.5 kg*

Normal

Use for

Drying microfibre fabric, skiwear, outerwear, fine, closeweave cotton

garments (poplin) or tablecloths which are suitable for drying in a

tumble dryer and have been treated to provide a water and dirt

resistant finish.

Notes

– This programme includes a proofing fixing phase.
– Only use proofing agents containing fluorochemical compounds

which are stated by the manufacturer as being "suitable for use

on membrane textiles".

– Do not dry items which have been treated with proofing agents

containing paraffin. Fire hazard!

Delicates

Max. load 2.5 kg*

, Normal, Slightly dry, Hand iron



, Hand iron



Use for

Delicate items with the



symbol on the care label made of

synthetic fibres, easy care cotton or blended fabric, e.g. shirts,

blouses, lingerie and evening wear with sequins and beading.

Note

Reducing the load will reduce creasing.

Automatic plus

Max. load 5.0 kg*

, Normal, Slightly dry, Hand iron



, Hand iron



Use for

Mixed loads of garments suitable for the

Cottons

and

Minimum iron

programmes.

* Weight of dry laundry

Summary of Contents for TMG 440 WP





















































































Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands

Miele TMG 440 WP, Operating Instructions Manual

Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands