Miele TMG 440 WP Operating Instructions Manual Download Page 43

Page: 43 / 84

Cleaning and care

Cleaning the plinth filter panel



Use a damp cloth to remove any fluff.

Make sure that you do not damage

the rubber seal when doing this.



Check whether the cooling fins are

blocked with fluff (as follows).

Checking the heat exchanger



Danger of injury. Do not touch

the cooling fins. You could cut

yourself.



Look to see if fluff has accumulated.

If there is visible soiling:



Clean using a vacuum cleaner

with a dusting brush attached.

Carefully pass the vacuum cleaner

brush over the heat exchanger

cooling fins without applying any

pressure. Otherwise the cooling fins

could be bent out of shape or

become damaged.



Carefully vacuum up any visible

soiling.

Summary of Contents for TMG 440 WP





















































































Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands

Miele TMG 440 WP, Operating Instructions Manual

Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands