Miele TMG 440 WP Operating Instructions Manual Download Page 42

Page: 42 / 84

Cleaning and care

Plinth filter

Only clean the plinth filter when

Clean out airways

lights up.

To delete

Clean out airways

: Switch the

dryer off and back on again / confirm

Removing the plinth filter



Press the round, indented area on the

heat exchanger access panel to open

it.

The panel will spring open.



Pull the plinth filter out by the handle.

Removing the plinth filter will cause the

right hand guide pin in the dryer to

come out. This pin ensures that the

heat exchanger access panel can only

be closed if the plinth filter is inserted

the right way round.

Cleaning the plinth filter

aaa

aaaaaaa

a a a aaa



Pull the handle out of the plinth filter.



Clean the filter thoroughly under

running water.



Squeeze the plinth filter thoroughly.



The plinth filter must not be

replaced dripping wet as this can

cause a fault.



Use a damp cloth to remove any fluff

from the handle.

Summary of Contents for TMG 440 WP





















































































Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands

Miele TMG 440 WP, Operating Instructions Manual

Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands