Miele TMG 440 WP Operating Instructions Manual Download Page 77

Page: 77 / 84

Settings menu

Drying levels

You can alter the drying levels for the

Cottons

Minimum iron

and

Automatic

plus

programmes.

The setting selected is shown in a bar

chart.
Factory default: a medium setting

– Damper

      

The programme duration is shorter.

– Drier

      

The programme duration is longer.

Exception:

The

Cottons



programme will

remain unchanged.

Extended cool down

The automatic cooling down phase

which takes place before the end of a

programme can be extended for all

programmes with selectable drying

levels in 2 minute increments up to 18

minutes. This makes the garments

easier to handle.

Options

– 00 minutes (factory default)
– 02, 04, 06 ... 18 minutes

Airways indicator

Fluff should be removed after drying.

The

Clean out airways

message will

remind you to clean the filters when a

certain amount of fluff has collected in

them. You can decide at what level of

fluff this reminder should be given.

You will have an idea of how often this

should be done after a few drying

programmes.
Options

– Off

Clean out airways

does not appear.

In cases of a very severe blockage in

the airways, the programme will be

cancelled and the

Clean out airways

message will appear regardless of

this option.

– Heavy

Clean out airways

only appears when

there is a heavy build-up of fluff.

– Normal (factory default)
– Light

Clean out airways

appears when

there is only a small build-up of fluff.

Summary of Contents for TMG 440 WP





















































































Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands

Miele TMG 440 WP, Operating Instructions Manual

Search results

Summary of Contents for TMG 440 WP

Reviews:

Related manuals for TMG 440 WP

Brands by name

Popular brands