Miele T 4452 C Operating Instructions Manual Download

Page: 52 / 56

Airways indicator

The

Clean out airways

indicator light

can be deactivated.

The

Clean out airways

indicator light

– is activated when the machine is

delivered. The light is a reminder to
clean the fluff filters and to check
and clean the condenser unit, if
necessary. (see "Problem solving
guide").

– should only be deactivated if you are

certain that the fluff filters will be
cleaned after every drying
programme and that the condenser
unit will be checked and cleaned,
regularly.

Follow steps

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the

Start/Stop

indicator light

comes on . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button five times.

– The

Buzzer

indicator light will slowly

flash on and off once.

–

and

will flash alternately in the

display
(factory default setting).

Press the

Start/Stop

button

repeatedly until

–

and

appear in the display

Clean out airways

indicator light

deactivated

–

and

appear in the display

(the

Drying

indicator light will also flash):

Clean out airways

indictor light

activated
(factory default setting)

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. To change the setting
repeat steps

Programmable functions

Summary of Contents for T 4452 C

























































Search results

Summary of Contents for T 4452 C

Reviews:

Related manuals for T 4452 C

Brands by name

Popular brands

Miele T 4452 C, Operating Instructions Manual

Search results

Summary of Contents for T 4452 C

Reviews:

Related manuals for T 4452 C

Brands by name

Popular brands