manualshive.com logo in svg

Miele T 4452 C, Operating Instructions Manual

Share
Download
Miele T 4452 C Operating Instructions Manual Download Page 20

Smoothing

Max. load: 2.5 kg*

Fabric type

–

Cottons and linen fabrics.

–

Minimum iron items made of mixed fibres, e.g. cottons /
synthetics, such as cotton trousers, jackets, shirts.

Notes

–

Smooths out creasing caused during the spin cycle in the
washing machine.

–

Fabrics are not completely dried in this programme. Remove
garments immediately at the end of the programme and place on
a line or hangers to dry.

Extras

Anti-crease

Automatic / Normal / Hand iron

r

Max. load: 3 kg*

Fabric type Mixed load of cotton and minimum iron fabrics.

Notes

Select

Hand iron

r

for garments which are still to be hand ironed.

Extras

Anti-crease

Cool air

Max. load: 5 kg*

Fabric type Any item which only needs airing.

Extras

Anti-crease

Warm air

Max. load: 5 kg*

Fabric type

–

Multi-layered fabrics whose layers have different drying
characteristics such as jackets, pillows.

–

For drying individual items, e.g. bath towels, bathing costumes,
tea-towels.

Extras

Low temperature, Anti-crease

Notes

Do not select the longest drying time to start with. Check the items
as you are drying them to find the optimum time.

* Weight of dry laundry

Programme chart

20

Summary of Contents for T 4452 C

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands