Miele T 4452 C Operating Instructions Manual Download

Page: 48 / 56

Cottons drying level

If you want the laundry to be drier
you can reduce the residual moisture
level for the Cottons programmes.

– The programme duration will

increase and the laundry will be
drier.

– The machine is delivered with the

residual moisture level set at normal.

Follow steps

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the

Start/Stop

indicator light

comes on . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button once.

– The

Buzzer

indicator light will flash

briefly on and off twice.

–

and

will flash alternately in the

display
(factory default setting).

Press the

Start/Stop

button

repeatedly until

–

and

appear in the display

(the

Drying

indicator light will also flash):

Residual moisture level - drier

–

and

appear in the display

Residual moisture level - normal
(factory default setting)

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. To change the setting
repeat steps

Programmable functions

Summary of Contents for T 4452 C

























































Search results

Summary of Contents for T 4452 C

Reviews:

Related manuals for T 4452 C

Brands by name

Popular brands

Miele T 4452 C, Operating Instructions Manual

Search results

Summary of Contents for T 4452 C

Reviews:

Related manuals for T 4452 C

Brands by name

Popular brands