Miele T 4452 C Page 14 Operating Instructions Manual Download

Page: 14 / 56

Selecting a drying level

You can a select a drying level for the

Cottons, Minimum iron and Automatic

programmes.

You cannot select a drying level for the
other programmes. If you have
selected one of these other
programmes, please proceed to
"Selecting the buzzer".

Press the DRYING LEVEL button
repeatedly until the indicator light for
the drying level you want comes on.

Any of the drying levels can be
selected for the

Cottons

programme. A

more limited range is available when
using the

Minimum iron

and

Automatic

programmes.

Selecting the buzzer

A buzzer sounds (at intervals for a
maximum of 1 hr) to let you know the
programme has finished.

Press the

Buzzer

button.

Indicator light on =

Buzzer

selected

The buzzer will always sound when
there is a fault, even if the buzzer has
been switched off.

You can change the volume of the
buzzer.

Before you begin, first ensure that:

– the dryer is switched on

– the door is closed.

– you have selected a programme

1. If the

Buzzer

indicator light is on:

press the

Buzzer

button so that the

indicator light goes out.

2. Press the

Buzzer button (the buzzer

indicator light must be on), until the
desired volume / pitch is achieved.
Then release the button.

Selecting delay start

The start of a programme can be
delayed by up to 24 hours.

How to dry correctly

Summary of Contents for T 4452 C

























































Search results

Summary of Contents for T 4452 C

Reviews:

Related manuals for T 4452 C

Brands by name

Popular brands

Miele T 4452 C, Operating Instructions Manual

Search results

Summary of Contents for T 4452 C

Reviews:

Related manuals for T 4452 C

Brands by name

Popular brands