Miele PW 811 Operating And Installation Instructions Download Page 37

Page: 37 / 184

Washing by card operation

Cards with

at least one

programme are intended for a particular type

of machine. Blank cards can be used in any machine.



Switch on the machine with the

"Power On" button.

The welcome screen will appear in the display.



Insert the card.

The programmes on the card will appear in the display.

Card operation

Masks

Minimum iron









°C



Select a programme by turning the multifunction selector. Press the
multifunction selector to highlight the programme.



Select the highlighted programme by pressing the multifunction
selector.



Press the "START" button.

The programme will start running.

Useful tip:

After the "START" button has been pressed, the card can

be removed from the card reader. The programme will be deleted at
the end of the programme.

Do not insert any objects other than the card into the card slot.

If the card is inserted into the slot the wrong way, the following
message will appear in the display:

Card fault

Card incorrectly inserted in card reader.







Insert the card into the card reader correctly.

Summary of Contents for PW 811

























































































































































































Search results

Summary of Contents for PW 811

Reviews:

Related manuals for PW 811

Brands by name

Popular brands

Miele PW 811, Operating And Installation Instructions

Search results

Summary of Contents for PW 811

Reviews:

Related manuals for PW 811

Brands by name

Popular brands