manualshive.com logo in svg

Miele PT 7137 WP Vario, Operating And Installation Instructions

Share
Download
Miele PT 7137 WP Vario Operating And Installation Instructions Download Page 41

Problem solving guide

41

Problem

Cause and remedy

 

Power failure Programme

stopped Press OK button

The tumble dryer was switched off during a pro-
gramme or there has been a power cut.

Press the 

OK

 button after switching the dryer back

on and start the programme again.

 

Clean plinth filter

The filter is blocked or the surfaces of the fluff filters
are heavily soiled.

Clean them as described in "Cleaning and
care". . .
. . . "Filter in the plinth"
. . . "Cleaning the fluff filters"

Confirm with 

OK

.

 

Open bottom right grille.

Clean airways

The cooling fins behind the grille can become blocked
with dust and dirt drawn in from the surrounding area
and the airways can become blocked with fluff.

Clean as described in "Cleaning and care - Bottom
right grille/airways"

Also check and clean the filter in the plinth and
surfaces of the fluff filters.

Confirm with 

OK

.

You can adjust the settings which control if or when
this message appears.

 

Fit plinth filter or put it in

the other way around

The filter in the plinth is missing or inserted incor-
rectly.

Check the filter in the plinth.

Removing the filter during a drying programme will
result in the cancellation of the programme.

 

Drain fault Check the

drainage system.

The drain hose kinked.

Remove the kink.

To delete the fault message: Confirm with 

OK

.

Summary of Contents for PT 7137 WP Vario





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands