manualshive.com logo in svg

Miele PT 7137 WP Vario, Operating And Installation Instructions

Share
Download
Miele PT 7137 WP Vario Operating And Installation Instructions Download Page 26

Selecting a programme

26

Selecting/changing a programme

Entry menu

1

2

3

4

10:00

Cottons

Minimum iron

Woollens

Smoothing

Programme selection

Settings

...

...

Press short cut button 

Main menu

Cottons

Normal

Back

Duration

Timer

h

Save

G-tumble

1:30

By turning the multi-function selector you can then highlight
the following options in the display: Programme (

Cottons

) or

the drying level (

Normal

) and confirm your selection by

pressing the multi-function selector.

Depending on the option highlighted, the following will be
displayed:

– Programme selection

Back

Cottons

Minimum iron

Woollens

Programme
selection

Use the multi-function selector to select the programme you
want, and confirm your selection. The main menu will re-
appear.

Note: If you do not make a selection in the sub-menu within
approx. 20 seconds, the display will revert to the main menu.

Summary of Contents for PT 7137 WP Vario





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands