manualshive.com logo in svg

Miele PT 7137 WP Vario, Operating And Installation Instructions

Share
Download
Miele PT 7137 WP Vario Operating And Installation Instructions Download Page 40

Problem solving guide

40

With the help of the following notes minor faults in the performance of the appli-
ance, some of which may result from incorrect operation, can be put right without
contacting the Service Department.

Repair work to electrical appliances should only be carried out by a suitably

qualified person in strict accordance with current local and national safety regu-
lations. Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held liable for unauthorised work.

Check and fault messages in the display

Problem

Cause and remedy

 

Adjust the load The drum

is empty, or the laundry is
too dry.

appears when a pro-
gramme has been can-
celled.

This is not a fault. 
In some programmes, if the drum has been under-
loaded or is empty, the programme will be cancelled.
This can also happen if the items are already dry.

Open and close the door to resume drying.

Dry individual items using the 

Warm air

 timed dry-

ing programme.

 

Technical fault

If restart is unsuccessful, call
Service.

A fault number (e.g.
F157) might also be dis-
played.

No obvious cause.

Make a note of what is shown in the display.

Start a programme.

If the programme is cancelled again and an error
message appears, there is a fault. Contact Miele ser-
vice.

Summary of Contents for PT 7137 WP Vario





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands