Miele PG 8131i Operating Instructions Manual Download Page 65

Page: 65 / 92

Problem solving guide

Unsatisfactory cleaning result

Problem

Cause and remedy

The dishes are not
clean.

The dishes were not loaded correctly.



See notes in “Loading the dishwasher”.

The programme was not suitable for the load.



Select a more suitable programme (see “Pro-
gramme chart”).

Not enough detergent was dispensed.



Increase the dosage.

The detergent used is not suitable for the type of soil-
ing present.



Change your detergent.

Items are blocking the path of the spray arms.



Rearrange the items so that the spray arms can ro-
tate freely.

The filter combination in the base of the wash cabinet
is not clean or is not correctly fitted.
This may have caused the spray arm jets to get
blocked.



Clean and/or fit the filter combination correctly.



Clean the spray arm jets if necessary (see “Clean-
ing and care - Cleaning the spray arms”).

The non-return valve is open and blocked. Dirty water
has flowed back into the wash cabinet.



Clean the drain pump or the non-return valve (see
“Maintenance”).

Smearing appears on
glassware and cutlery.
There is a bluish sheen
on the surface of glass-
ware; film can be wiped
off.

The rinse aid dosage is set too high.



Reduce the dosage (see “Settings menu, Rinse
aid”).

Summary of Contents for PG 8131i





























































































Search results

Summary of Contents for PG 8131i

Reviews:

Related manuals for PG 8131i

Brands by name

Popular brands

Miele PG 8131i, Operating Instructions Manual

Search results

Summary of Contents for PG 8131i

Reviews:

Related manuals for PG 8131i

Brands by name

Popular brands