background image

Loading the dishwasher

33

Adjusting the upper basket

In order to gain more space for taller
pieces of crockery in the lower or upper
basket, the upper basket can be adjus-
ted on three levels with 2 cm between
each level.

The upper basket can also be set at an
angle with one side high and the other
side low. This can be useful to help pre-
vent water being left in deep dishes etc.
Ensure, however, that the basket can
be inserted smoothly into the cabinet. It
is better to adjust the basket before
loading it.

Pull out the upper basket.

To raise the upper basket:

Lift the basket up until it clicks into
place.

To lower the upper basket:

Pull upwards on the levers at either
side of the upper basket.

Adjust the basket to the desired
height and then push the levers se-
curely back down into position.

Depending on the setting of the upper
basket, the following plate dimensions
can be accommodated.

Dishwashers with cutlery basket 

(see data plate for model number)

Upper

basket

level

Plate 

 in cm

Upper basket

Lower

basket

Stand-

ard

XXL

Top

20

24

31 (35*)

Middle

22

26

29

Bottom

24

28

27

* When tilted, plates of up to 35 cm can
be accommodated (see "Lower basket).

Summary of Contents for PG 8131i





























































































Reviews: