Miele HG07-W Page 103 Operating Instructions Manual Download

Page: 103 / 124

Problem solving guide

103

Spray arm fault

Issue

Cause and remedy

During the programme
and at the end of the
programme, the display
shows the following
message:

Check spray arms

The dishwasher does
not switch off at the end
of the programme.
The wash items may not
be clean because no
detergent was
dispensed. The



AutoDos

function is

automatically
deactivated during the
programme.

The lower spray arm is blocked or the jets of the
lower spray arm are clogged. The



AutoDos

function is automatically deactivated

during the programme because the AutoDos
detergent outlet cannot be completely flushed out.



Switch the dishwasher off and back on again.

Messages appear in the display.



Perform a rotation check of the lower spray arm
and rearrange the wash items if they are blocking
the spray arm.



Clean the lower spray arm (see “Cleaning and
care” chapter, “Cleaning the spray arms” section).



Select

to confirm each message.



Start the programme again.

Summary of Contents for HG07-W





























































































































Search results

Summary of Contents for HG07-W

Reviews:

Related manuals for HG07-W

Brands by name

Popular brands

Miele HG07-W, Operating Instructions Manual

Search results

Summary of Contents for HG07-W

Reviews:

Related manuals for HG07-W

Brands by name

Popular brands