Miele HG07-W Page 107 Operating Instructions Manual Download

Page: 107 / 124

Problem solving guide

107

Issue

Cause and remedy

The crockery is not dry
or cutlery and glasses
are flecked.

The rinse aid dosage is too low or the rinse aid
container is empty.



Replenish the rinse aid container, increase the
dosage or change the brand of rinse aid (see
“Before using for the first time – Rinse aid”).

The crockery was taken out of the wash cabinet too
soon.



Leave the crockery in longer (see “Operation –
Unloading the dishwasher”).

The duration of the drying phase for the selected
programme is not sufficient for the crockery
(particularly for plastic crockery).



Select the Extra dry function (see “Settings –
Extra dry”).

You have used combination products that have
insufficient drying performance.



Switch to another detergent, or replenish the rinse
aid (see “Before using for the first time – Rinse
aid”).

Glassware has a brown
or blue tinge. The film
cannot be wiped off.

Ingredients from the detergent have formed a
deposit.



Switch to another detergent straight away.

Glassware is dull and
discoloured. The film
cannot be wiped off.

The glassware is not dishwasher-proof. The surface
has altered.



No remedy.
Purchase glassware that is dishwasher-proof.

Tea or lipstick stains
have not been
completely removed.

The wash temperature of the selected programme
was too low.



Select a programme with a higher main wash
temperature.

The bleaching effect of the detergent used is too low.



Switch to another detergent.

Summary of Contents for HG07-W





























































































































Search results

Summary of Contents for HG07-W

Reviews:

Related manuals for HG07-W

Brands by name

Popular brands

Miele HG07-W, Operating Instructions Manual

Search results

Summary of Contents for HG07-W

Reviews:

Related manuals for HG07-W

Brands by name

Popular brands