Miele HG07-W Page 87 Operating Instructions Manual Download | Manualshive

Page: 87 / 124

background image

Cleaning and care

87



Clean the pouring channel using
water and a soft brush if necessary.

It is very important that no moisture
is able to access the inside of the
AutoDos system during cleaning.



Dry the pouring channel well so that
the detergent powder does not clump
together.



Insert the pouring channel again until
the tab clicks into place.



Put the holder back into place so that
the arrows in the PowerDisk holder
and in the viewing window point
towards each other. The holder must
lie flat.

The AutoDos lid must close tightly so
that the detergent powder does not
get wet and clump together.
Make sure that all seals are clean.



Insert a PowerDisk.



Close the AutoDos lid and turn it until
the lid handle is directly below the



symbol. (see “Detergent” chapter,

“Inserting a PowerDisk” section).

Regularly check the lower spray arm
for any blockages to ensure that the
detergent outlet of the AutoDos can
be fully flushed out (see “Cleaning
and care” chapter, “Cleaning the
spray arms” section).

«
...
85
86
87
88
89
...
»

Summary of Contents for HG07-W





























































































































Reviews:

No comments

Related manuals for HG07-W

Brand: GE Pages: 5

Brand: Dawlance Pages: 44

Summit DW18SSADA

Brand: Accucold Pages: 2

Brand: Blomberg Pages: 44

Brand: Daewoo Pages: 31

Brand: lamber Pages: 43

Brand: Heinner Pages: 58

Spacemaker WSM2780R

Brand: GE Pages: 56

Brand: Atag Pages: 60

Brand: Indesit Pages: 20

Brand: WST Pages: 4

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 29

Brand: Electrolux Pages: 16

Brand: Electrolux Pages: 32

Brand: Electrolux Pages: 22

Brand: Electrolux Pages: 22

Brand: Electrolux Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands