Miele HG07-W Page 40 Operating Instructions Manual Download | Manualshive

Page: 40 / 124

background image

Settings

40

RemoteUpdate

The RemoteUpdate menu option is
only displayed and can only be
selected if the requirements for using
Miele@home have been met (see
“Before using for the first time”
chapter, “Miele@home” section).

The RemoteUpdate function is used for
updating the software in your
dishwasher. If an update is available for
your dishwasher, it will automatically
download it. Updates will not be
installed automatically. They must be
initiated manually.

If you do not install an update, you can
continue to use your dishwasher as
usual. However, Miele recommends
installing updates.

Activating/deactivating

The RemoteUpdate function is
activated as standard. Available
updates will be downloaded
automatically and will only be installed if
you initiate them.

Deactivate RemoteUpdate if you do not
wish any updates to be downloaded
automatically.

Running a RemoteUpdate

Information about the content and
scope of a RemoteUpdate will be
provided in the Miele@mobile app.

A message will appear in your
dishwasher display if a software update
is available.

You can install the update immediately
or postpone it until later. When the
appliance is switched on again, you will
be reminded about the update.

Switch RemoteUpdate off if you do not
wish to install updates.

Updates may take several minutes.

Please note the following information
about the RemoteUpdate function:

- You will only receive a message when

an update is available.

- Once an update has been installed, it

cannot be undone.

- Do not switch the dishwasher off

during the update. Otherwise, the
update will be aborted and will not be
installed.

- Some software updates can only be

carried out by your Miele dealer.

«
...
38
39
40
41
42
...
»

Summary of Contents for HG07-W





























































































































Reviews:

No comments

Related manuals for HG07-W

Brand: Dacor Pages: 32

Brand: IFB Pages: 33

Brand: Magic Chef Pages: 30

Brand: Magic Chef Pages: 8

Brand: Sammic Pages: 48

Brand: Artusi Pages: 46

Brand: Clatronic Pages: 42

Brand: Proline Pages: 16

Brand: Solt Pages: 11

Brand: Smeg Pages: 17

SWF1076 EZI SENSOR

Brand: Simpson Pages: 32

Brand: Alliance Laundry Systems Pages: 19

Brand: Morris Pages: 25

Brand: Haier Pages: 22

Brand: Haier Pages: 40

Brand: Haier Pages: 19

WA16CG6745 Series

Brand: Samsung Pages: 48

WA14N6780C Series

Brand: Samsung Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands