manualshive.com logo in svg

Miele HG07-W, Operating Instructions Manual, Page: 39 / 124

Share
Download
Miele HG07-W Operating Instructions Manual Download Page 39

Settings

39

Reset

This menu option only appears if you
have already connected your
dishwasher to your WiFi network.

You can use this menu option to reset
all WiFi module settings to the factory
default settings.

The network configuration should be
reset whenever a dishwasher is being
disposed of or sold, or if a used
dishwasher is being put into operation.
This is the only way to ensure that all
personal data has been removed and
the previous owner will no longer be
able to access the dishwasher.

Select the 

Reset

 menu option and

confirm with 

OK

.

Remote control

This menu option will only be
displayed if you have connected your
dishwasher to your WiFi network (see
“Settings” chapter, “Miele@home”
section)

If you wish to permanently switch off
the 

Remote control

 option, you can do

this under this menu option. The

 sensor control will then no longer be

available to select until you change this
setting again.

Even if the 

Remote control

 option is

switched off, you can use Miele@mobile
to call up information about your
appliance. However, you cannot start
any programmes or change any
settings from it.

Summary of Contents for HG07-W





























































































































Reviews:

No comments