Miele HG07-W Page 34 Operating Instructions Manual Download

Page: 34 / 124

Settings

Language



The display can be set to appear in one
of several different languages.

You can change the language used in
the display and also the country via the

Language 

sub-menu.

The flag after the word

Language 

serves as a guide if a language that
you do not understand has been set.
In this case keep selecting the menu
option that has a flag after it until you
reach the

Language 

sub-menu.

Time of day

The current time of day must be set
before you can use the timer option.

Setting the clock format

You can select either a 24-hour or 12-
hour clock.



Select the

Clock format

menu option.



Select the setting you want and
confirm with

Setting the time of day

You can set the current time of day.



Select the

Set

menu option.



Use the



sensor controls to enter

the hour and confirm your entry by
touching

Then set the minutes and confirm
with

The time of day has now been saved.

Summary of Contents for HG07-W





























































































































Search results

Summary of Contents for HG07-W

Reviews:

Related manuals for HG07-W

Brands by name

Popular brands

Miele HG07-W, Operating Instructions Manual

Search results

Summary of Contents for HG07-W

Reviews:

Related manuals for HG07-W

Brands by name

Popular brands