Miele G 7110 Operating Instructions Manual Download Page 89 | Manualshive

Page: 89 / 120

background image

Cleaning and care

89



In order to clean the inside of the
filter, pull the microfilter on the plastic
ring downwards and away from the
filter combination.



Rinse all the parts under running
water.
If necessary, use a soft cleaning
brush to remove soiling.



Insert the microfilter back into the
filter combination.



Refit the filter combination so that it
lies flat in the base of the wash
cabinet.



Refit the lower spray arm to the filter
combination using the screw
connection.



Rotate the screw connection
clockwise until the arrow in the
viewing window points to the lock
symbol



.



Damage due to soiling entering

the circulation system.
The lower spray arm is used to
secure the filter combination.
Without filters, coarse soiling can
enter the circulation system and
cause a blockage.
Do not run a wash programme
without the lower spray arm or
without the filters.

«
...
87
88
89
90
91
...
»

Summary of Contents for G 7110

























































































































Reviews:

No comments

Related manuals for G 7110

Brand: GE Pages: 36

Brand: davoline Pages: 68

Brand: Haier Pages: 20

Brand: Wascomat Pages: 50

Brand: Magic Chef Pages: 25

Brand: Sammic Pages: 28

Brand: Hotpoint Pages: 2

Brand: Gaggenau Pages: 48

WA70H4200S Series

Brand: Samsung Pages: 48

Brand: Hansa Pages: 48

VRT PLUS WE357 Series

Brand: Samsung Pages: 96

Brand: Candy Pages: 49

Brand: FAR Pages: 105

Brand: GE Pages: 16

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands