Miele G 7110 Operating Instructions Manual Download Page 13

Page: 13 / 120

Warning and safety instructions



A damaged dishwasher could be dangerous. If the dishwasher

gets damaged, switch it off at the mains immediately and call your
Miele dealer.



While the appliance is under warranty, repairs should only be

undertaken by a Miele authorised technician. Otherwise the warranty
is invalidated.



We recommend replacing defective components with original

spare parts. If original Miele spare parts are installed correctly, Miele
ensures full compliance with safety requirements and the warranty
remains valid.



During installation, maintenance and repair work, the dishwasher

must be disconnected from the mains electricity supply (switch it off
and withdraw the plug from the socket).



If the connection cable is damaged it must be replaced with a

special cable of the same type (available from Miele). For safety
reasons this work must be carried out by a Miele authorised
technician only.

Correct installation



The dishwasher must be installed and connected in compliance

with the supplied installation sheet.



Be careful before and while installing the dishwasher.

Some metal parts pose a risk of injury/being cut. Wear
protective gloves.



The dishwasher must be correctly aligned horizontally to ensure

problem-free operation.



In order to ensure stability, built-under and integrated dishwashers

must only be installed under a continuous worktop that is secured to
adjacent cabinetry.

Summary of Contents for G 7110

























































































































Search results

Summary of Contents for G 7110

Reviews:

Related manuals for G 7110

Brands by name

Popular brands

Miele G 7110, Operating Instructions Manual

Search results

Summary of Contents for G 7110

Reviews:

Related manuals for G 7110

Brands by name

Popular brands