Miele G 7110 Operating Instructions Manual Download Page 83

Page: 83 / 120

Cleaning and care

Cleaning the AutoDos

If the

Clean AutoDos

message is

displayed, check that the fill channel
is clean, and clean it if necessary,
e.g. powder residues. This helps
keep the AutoDos working properly.

In order to ensure that the AutoDos
works at its best, check it each time
you replace the PowerDisk and clean
it if needed.

PowerDisk holder

Fill channel for dispensing the

detergent from the PowerDisk into the
wash cabinet



Turn the AutoDos lid to



and open

it.



Remove the PowerDisk if appropriate.



Pull the PowerDisk holder upwards
by the yellow tabs and remove it.
When doing so, do not pull on the
side tab.



Use the tab (see arrow)



to release

the fill channel and pull it out



Summary of Contents for G 7110

























































































































Search results

Summary of Contents for G 7110

Reviews:

Related manuals for G 7110

Brands by name

Popular brands

Miele G 7110, Operating Instructions Manual

Search results

Summary of Contents for G 7110

Reviews:

Related manuals for G 7110

Brands by name

Popular brands