Miele G 7110 Operating Instructions Manual Download Page 37

Page: 37 / 120

Settings

Miele@home

Your dishwasher is equipped with an
integrated WiFi module.

You can connect your dishwasher to
your WiFi network.
This will increase the energy
consumption, even when the
dishwasher is switched off.

The “Settings” and “Miele@home
settings” menus will be added as
additional menu options.

Make sure that your WiFi network
signal strength is strong enough at
the installation site of your
dishwasher.

There are a number of ways of
connecting your dishwasher to your
WiFi network:

Connect using App

The Miele app is available to download
free of charge from the Apple App
Store

or from the Google Play™ store.



Select the

Connect using App

option and confirm with



Follow the instructions in the app.

Once your dishwasher is connected to
your WiFi network you can use the app
to carry out the following activities:

- Control your dishwasher remotely

- Call up information on the operating

status of your dishwasher

- Call up information on the

programme sequence of your
dishwasher

- Set up a Miele@home network with

other WiFi-enabled Miele appliances

Summary of Contents for G 7110

























































































































Search results

Summary of Contents for G 7110

Reviews:

Related manuals for G 7110

Brands by name

Popular brands

Miele G 7110, Operating Instructions Manual

Search results

Summary of Contents for G 7110

Reviews:

Related manuals for G 7110

Brands by name

Popular brands