Miele G 7110 Operating Instructions Manual Download Page 38

Page: 38 / 120

Settings

Connect using WPS

As an alternative to networking via the
Miele app you can connect your
dishwasher to your WiFi network using
WPS (Wireless Protected Setup).

Your WiFi router must support WPS.



Confirm the

Press WPS

button

message with



Activate the WPS function on your
router within two minutes.



Once the connection has been
established, confirm the message
with

If the connection fails, you have
probably not activated WPS on your
router quickly enough. Repeat the steps
above.

Deactivate

If you do not wish to use the WiFi
module of your dishwasher, you can
switch it off.



Select the

Deactivate

menu option

and confirm with

In the

Miele@home

menu, the menu

option

Activate

will now be displayed

instead of

Deactivate

Activate

If you wish to connect your dishwasher
to your WiFi network, you can turn on
the WiFi module.



Select the

Activate

menu option and

confirm with

In the

Miele@home

menu, the menu

option

Deactivate

will now be displayed

instead of

Activate

Summary of Contents for G 7110

























































































































Search results

Summary of Contents for G 7110

Reviews:

Related manuals for G 7110

Brands by name

Popular brands

Miele G 7110, Operating Instructions Manual

Search results

Summary of Contents for G 7110

Reviews:

Related manuals for G 7110

Brands by name

Popular brands