Miele G 685 Operating Instructions Manual Download Page 47

Page: 47 / 88

Problem solving guide

With the aid of the following explana-
tory notes, minor faults can be cor-
rected without contacting the Miele Ser-
vice Department.

Any work on the electrical compo-
nents of the appliance should only
be carried out by a suitably quali-
fied and competent person in ac-
cordance with local and national
regulations. Unauthorised repairs
could be dangerous.

If, however, you are unable to correct
the problem, the Miele Service Depart-
ment should be contacted.

Faults/possible causes

The dishwasher does not start

– The door is not properly closed.

– The plug is not properly inserted.

– The fuse is defective/has blown.

The dishes are not cleaned

– The dishes are incorrectly loaded.

– The correct amount of detergent was

not dosed - see “Programme chart”.

– The filters in the wash cabinet are

not clean - see “Cleaning and care”.

– The spray arm jets are blocked - see

“Cleaning and care”.

– The wrong programme was selected

- see "Programme chart".

White residue on cutlery and
crockery

– No salt in the salt reservoir.

Fill the salt reservoir with dish-
washer salt for reactivation
- see section on "Water softener".

– Salt reservoir lid has not been

screwed on properly.

– Not enough rinse aid.

Use a higher dosage setting
- see "Adding rinse aid".

Problem solving guide

Summary of Contents for G 685

























































































Search results

Summary of Contents for G 685

Reviews:

Related manuals for G 685

Brands by name

Popular brands

Miele G 685, Operating Instructions Manual

Search results

Summary of Contents for G 685

Reviews:

Related manuals for G 685

Brands by name

Popular brands