Miele G 685 Operating Instructions Manual Download Page 27

Page: 27 / 88

Loading the dishwasher

Adjusting the upper basket

(depending on model)

In order to gain more space for taller
pieces of crockery in the bottom or
upper basket, the upper basket can be
adjusted in three steps with 2 cm be-
tween each step.

Pull out the upper basket and loosen
the two locknuts on either side of the
basket.

Adjust the basket up or down to the
right height.

Tighten the locknuts.

The upper basket can also be set to an
angle if required.

Depending on the setting of the upper
basket the following dimensions can be
accommodated:

Dishwashers with cutlery tray

Upper bas-
ket position

Upper

basket Ø

Lower

basket Ø

Top

15.5

Middle

17.5

Bottom

19.5

Dishwashers with cutlery basket

Upper bas-
ket position

Upper

basket Ø

Lower

basket Ø

Top

21.5

Middle

23.5

Bottom

25.5

Loading the dishwasher

Summary of Contents for G 685

























































































Search results

Summary of Contents for G 685

Reviews:

Related manuals for G 685

Brands by name

Popular brands

Miele G 685, Operating Instructions Manual

Search results

Summary of Contents for G 685

Reviews:

Related manuals for G 685

Brands by name

Popular brands