Miele G 685 Operating Instructions Manual Download Page 36

Page: 36 / 88

Switching on and off

Switching on

Close the door

Open the stopcock (if it is closed).

Press the “On/Off”-switch (14).

When the programme and temperature
selector switch (21) is in the “STOP” po-
sition a dot lights up in the display field
(17).

Starting a programme

Turn the Programme and tempera-
ture selector switch (21) clockwise or
anti-clockwise to the required pro-
gramme.

The length of the programme selected
appears in hours and minutes in the
Time display (17).

At the same time an indicator light il-
luminates next to the “START”-button
(18).

Before starting a programme select
additional options “Delay start” or
“Top Solo” if required
(see chapter “Additional options”).

Press the “START” button (18).

The indicator light next to the “START”-
button goes out. The programme
starts.

Sequence indication (20)

After starting a programme the se-
quence indicator light (20) show the ac-
tual programme stage reached in a pro-
gramme.

Switching on and off

Summary of Contents for G 685

























































































Search results

Summary of Contents for G 685

Reviews:

Related manuals for G 685

Brands by name

Popular brands

Miele G 685, Operating Instructions Manual

Search results

Summary of Contents for G 685

Reviews:

Related manuals for G 685

Brands by name

Popular brands