Miele G 685 Operating Instructions Manual Download Page 73

Page: 73 / 88

5. Fitting the (matching) door

front

The door of a kitchen base unit (without
the drawer facia or fittings) is normally
used for the door front.

The door front is fixed to the machine
door outer panel using a fixing bracket
which has to be pre-mounted on the
rear of the door front.

Fixing brackets are already fitted on to
the stainless steel door front. This front
cannot be shortened.

Door fronts differ in weight and it is
therefore essential that the door
springs are adjusted (see Step 6)
after the door front has been fitted.

Calculate dimension “

” and make a

note of it before attaching the fixing
bracket.

Dimension “

” is the dimension shown

on the illustration between the drill hole
in the outer door panel and the lower
edge of the neighbouring unit door(s).

Installing integrated “i” Dishwashers

Summary of Contents for G 685

























































































Search results

Summary of Contents for G 685

Reviews:

Related manuals for G 685

Brands by name

Popular brands

Miele G 685, Operating Instructions Manual

Search results

Summary of Contents for G 685

Reviews:

Related manuals for G 685

Brands by name

Popular brands