background image

Drainage

The machine drainage system is
fitted with a non-return valve, which
prevents dirty water from flowing
back into the machine via the drain
hose. 

The dishwasher is supplied with ap-
prox. 1.5 m of flexible drain hose
with an internal diameter of 22 mm.

The drain hose can be extended
using a connection piece and an
extra drain hose, (up to max. 4
metres).

If the hose is to be directly fitted to
the drainage outlet on site, use the
hose clip supplied.

The connection socket on the dish-
washer can be turned. The hose can
thus be laid to the right or left without
needing to loosen the hose clip.

The drain system must not exceed
4 metres. The drain pump has a
maximum delivery head of 1 metre.

The drain hose must not be short-
ened.

Venting the drainage system

Open the dishwasher door fully.

If the site drain connection is situated
lower than the guide path for the bot-
tom basket rollers in the open door the
drainage system must be vented.
Otherwise a siphoning effect during a
programme can cause the machine to
empty itself of water.

To vent:

Cut off the top of the vent valve in
the wash cabinet.

Plumbing

83

Summary of Contents for G 685

























































































Reviews: