Miele G 5481 Operating Instructions Manual Download Page 73

Page: 73 / 92

Problem solving guide

Fault messages

Problem

Possible cause and remedy

The warning buzzer is
sounding.
Fault number



appears in the time
display.

There may be a technical fault.



Switch the dishwasher off with the



button.



Switch the dishwasher back on after a few
seconds.



Select the required programme.



Close the door.

If the indicator lights flash again, there is a technical
fault.



Switch the dishwasher off.



Turn off the tap.



Call Miele.

Fault



The drain pump may
still be running, even
with the door open.

The Waterproof system has reacted.



Switch the dishwasher off.



Turn off the tap.



Call Miele.

The warning buzzer is
sounding.
When the door is open,
all of the programme
selection indicator
lights are flashing.
Fault number

78

appears in the time
display.

Circulation pump fault.



Switch the dishwasher off.



Switch the dishwasher back on.



Select the required programme.



Close the door.

If the fault message appears again, there is a
technical fault.



Switch the dishwasher off.



Turn off the tap.



Call Miele.

Summary of Contents for G 5481





























































































Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands

Miele G 5481, Operating Instructions Manual

Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands